‘But those who hope in the Lord will renew their strength. They will soar on wings like eagles; they will run and not grow weary; they will walk and not faint.’
One of the things that has always bothered me concerning woodworking forums, magazines, etc. has been an overemphasis on the spiritual/metaphysical aspects of making furniture. If there is one quality that I despise in anybody, it is an overabundance of self-importance. A lot of people, too many people, tend to over-value themselves, and the things they make, in relation to how they think others should perceive it. I had mentioned in an earlier post a trip to Mount Vernon and how that trip was in many ways a spiritual experience for me. Others may visit Mount Vernon just because they enjoy the grounds, and others still may visit and feel nothing at all. So when it comes to the Washington Campaign Desk I recently completed, I am very much in the mindset that it is without a doubt my favorite project, yet I would not doubt that some may look at it and think to themselves: ‘big deal!’
Firstly, as far as woodworking projects go, this desk, for someone at my skill level, would probably be considered an intermediate level project. For a professional woodworker it would likely be considered a relatively simple build. It was not the most technically difficult project I’ve made. In fact, I can say in all honesty that I spent as much time milling the wood and cleaning up the resulting mess as I did on the actual woodworking involved in constructing the desk. One of the most time consuming individual aspects of the project was making and fitting the breadboard ends, and when I carelessly removed a chunk of the desktop with a shoulder plane I wound up removing the ends completely rather than attempt a shoddy repair. If the two plus hours I spent on the breadboard ends are removed from the equation, I probably have more time spent milling than woodworking.
As in all of my projects, I like to think that I become a little better woodworker and learn a little bit more every time I complete one. But I cannot assign any one particular “Eureka” moment when it came to the physical act of working the wood used in making this desk. Probably the most challenging aspect of the construction was sawing and shaping the ogee ends. At that, the job I did was just okay. I certainly learned something, and I certainly gained some experience, but I don’t feel any closer to the woodworking gods in doing so.
After re-reading these few paragraphs you might thing that I sound bitter, or even ungrateful. Rest assured, I am neither. As I said, this project is hands down my favorite, and it is possible that I may never build anything again that I like quite as much. Why? It is simple, really. I went to a museum and caught a brief glimpse of a piece of furniture that was likely used by a person who has very much guided me throughout my life, and I knew enough about woodworking to be able to construct a near-enough reproduction of that piece of furniture using only a memory and a photo. If there is any “spirituality” to be found, this is it. When I saw the desk I knew immediately that I had to make it. I experienced a unique moment of true inspiration. I wasn’t looking for it; it wasn’t forced; it just happened. And in my estimation, that is the essence of spirituality.
There is more of me in that desk than in any other piece of furniture I’ve made. It isn’t in the joinery, which is dadoes, bolts, and a few screws. It isn’t in the desktop, which quite frankly has a bit more “character” than I had hoped, or the drawers, which are made of basic home center poplar held together with some basic half-blind dovetails. It is something that can’t be seen by others, and I’m glad of that fact.
I could write ten more pages trying to explain my reasonings, but I’m not going to do that. Just know that when I look at that desk, I feel connected to something larger than myself. And I believe that when I finally use it, I will be inspired to be my best.
I don’t know if there is a “woodworking god” or not. But if there is, just for a brief moment as this desk was nearing completion, I believe that I saw His face
For all intents and purposes I completed the construction phase of the Washington Campaign Desk over the weekend. On paper there wasn’t much left to do. Basically I had to assemble the drawer compartment parts and attach it to the desk top. But we all know that “on paper” doesn’t mean much.
Assembling the drawer compartment wasn’t overly difficult. I pre-drilled and counter-sunk the screw holes, applied a little glue, and screwed it together. That part was relatively easy. I had one minor issue, and that was the right side drawer divider would, for some reason, not sit perpendicular to the desk top. I double and triple checked the dado fit and no matter what I did I could not get it perfectly straight. Don’t get me wrong, it is not off much, probably 1 mm or so (for all you metric people), so I decided to not let it bother me. To finish it off I used walnut plugs purchased from Rockler; they worked surprisingly well, and I’m very happy with the finished appearance.
In the meanwhile, I also pre-drilled and counter sunk the holes in the desk top to attach it to the leg assemblies (using elongated holes to allow for movement). But before I went any further I disassembled the base and spent a good 90 minutes with a hand plane and sandpaper cleaning the parts up for finish. As far as the sanding was concerned, I used the grit sequence 60/120/220/320. I did not use a random orbit sander, rather, I just used a sanding block because it seemed easier to control, though it was definitely more time consuming. Once the sanding was finished I reassembled the legs, and thankfully I marked all of the parts before I took them apart to assure that I would put them back together correctly. I used a little glue to attach the filler pieces to the leg cleats, but otherwise, the only glue used in the entire project was on the four dadoes on the drawer compartment, and the walnut plugs. (I promise once it is finished, with finish, I will photograph all of the relevant parts). With the leg assemblies ready to go, I attached them to the desktop and reattached the cross cleat, once again plugging the countersunk holes and cleaning them up.
The last part of the assembly for me was the scariest, and that was attaching the drawer unit to the desktop. Before I took everything apart I marked and predrilled holes into the desktop. To attach the drawer unit I decided to use pocket-hole screws. I like using pocket-hole screws in situations like this because of the pan head holds nicely on elongated holes. In any case, I used two combination squares (I highly recommend having two BTW) to align the drawer unit, enlisted my lovely wife to hold the drawer unit in place, and carefully screwed the drawer unit to the desk top. Speaking for myself, it’s always a bit nerve wracking lying on my back and screwing through a tabletop sight unseen. Thankfully, everything went well.
And speaking of pocket screws, I may attach a cleat underneath the desktop to connect the two leg assemblies, just for added strength, because as of right now they are only connected by one cross brace. After doing some research it appears that pocket screws were traditionally used for such a task, believe it or not, but as of right now I still haven’t made up my mind.
The last task of the day was milling up some poplar for making the drawers. The drawer fronts were completed last week, but I didn’t want to plane them to final size until the drawer unit was assembled. I decided to go with half-blind dovetails for the drawers, which is the logical choice. So I gang sawed all four drawer sides at once, tails first obviously. I am holding off on the drawer backs just to make sure there is no settling, or what have you, before I glue the drawers together, but that part should only take a matter of minutes.
As far as the finish is concerned, when I started the project I spent some time searching the forums to find a nice finish for Walnut and kept coming back to a product called Sam Maloof poly/oil. It seemed to get good reviews, so I ordered a can of both the poly/oil and the poly/wax. The instructions call for 3 to 4 coats of the oil and 1 to 2 coats of the wax, with an overnight dry in between each application. I likely won’t start applying the finish until this coming Friday night, when I will have time to take my time.
And on another note, I am not overly concerned with the finish when it comes down to it. I used to worry a great deal about having a perfectly smooth, plastic-like appearance. But considering that the boards used to make this desk likely came from barn walls, I am more than happy with how it looks. I was more concerned with doing the best job I could do, and I believe that I did that. The desk looks like I want it to look, and I believe that it is well constructed and it should last for quite a while. I think that George Washington would have liked it, and more importantly, my daughter loves it, and I have a feeling that she will be the one to use it most, and that is about all I could ask.
It’s always reassuring to see my posts from 3 years ago make an appearance in places unlooked-for…I find it flattering.
This past weekend I began the scary phase of every one of my woodworking projects, and that is the time when there are a lot of almost finished, unassembled parts lying around waiting to be destroyed.
First things first, on Saturday afternoon/evening I spent two hours milling up the final two boards needed to complete the project. Well, it was about an hour milling up and an hour cleaning up. Rather than calling it a night, I wanted to get in a little actual woodworking, so I attached the cross brace to the back legs. I did not want to mortise out the legs because they are thin to begin with, so instead I dadoed the brace, 3/8 of an inch, planed it down, chamfered the edges, and sanded it smooth. I was satisfied with the appearance, so I attached it with some decorative brass screws. Thankfully, it added some much needed stability to the legs. Admittedly it took longer than it should have to lay out the dadoes, but I wanted the fit to be dead accurate, and I really didn’t want to waste a perfectly good board just by being careless.
Overnight Saturday we had a wind storm, so I spent a portion of the morning and early afternoon cleaning up the back yard, which really ate up the prime hours of the day. But I soldiered on and decided to get as much of the drawer unit finished as possible.
I took my sweet time with those dadoes, because I only had one crack at it, and once the kerfs were all sawn I used a chisel and router plane to get to finished depth. The fit was nice, so I moved on to what I believe is the most challenging part of this project, the ogees on the drawer compartment sides.
Considering that nearly all of the furniture I’ve built to date has been in the Arts & Crafts style (as well as some Shaker pieces), laying out and sawing an ogee with a coping saw is not my strong suit, but I decided to give it a try regardless. I used a compass and my limited artistic ability to lay out the ogee on one of the drawer unit ends, clamped both together, and started sawing. The results were mixed; I should have stuck closer to the line, but in the end it was done. Afterwards, I spent a good hour using a spoke shave, chisel, and rasp to get the pieces in shape. In the end, I wound up with more of a sloping cove than a true ogee, but I am not unhappy with it, and once it is sanded down I think it will look pretty good.
The last task of the day was adding rabbets to the side pieces of the drawer unit, which I did with a moving fillister plane. I could have pushed it and fitted the drawer dividers as well, but that part should be simple, and I didn’t want to push it, as it was getting late and I had a lot of clean up to do.
After clean up, I once again brought all of the parts into my family room for safe keeping. I attached the “ogeed” ends to the drawer unit top and placed it on top of the desk. I liked the open appearance, so I think what I may do is leave the space in between the two drawers without a back, just to see how it looks. If I don’t like it, I will simply add the filler piece, but I think that open area may add some lightness to the desk, and I could always bore out a space for an inkwell cup there.
Happily, so far none of the pieces have been damaged in any way. By the end of next week the desk should be ready for finish, as the only thing really left to do is make the drawers along with finishing up some light sanding. I’m hoping that my lovely wife steps in and does the finishing for me, as she is much more patient than I am when it comes to stuff like this. Otherwise, I am in the home stretch. And for those of you who celebrate the holiday, have a Happy Thanksgiving.
My favorite part of any furniture project is the point when a solution has been found to a challenge. It’s a figurative crossing of the “hump” which then signifies hopefully smooth sailing moving forward. This past Saturday I crossed that hump.
The bad news first. The temperatures in the area dropped well below freezing, and though that is not unheard of in my neck of the woods, it is uncommon for this time of year. So after I returned home from work on Saturday the first thing I did was check on the desk top panel. The panel is just fine, but the breadboard end with the issue was not looking so good. The underside developed a split that was instantly noticeable. Maybe the cold exaggerated it, but at that point I didn’t care, so the instant decision was made to saw off both of those bread board ends, which I did using the table saw and a cross-cut sled. I understood it meant losing a few hours of work, but I know the decision was the correct one because I felt no real remorse then or now, and rather than dwelling on it, I moved on to putting together the leg assemblies.
The leg assemblies posed a bit of a challenge, at least to me they did. Firstly, I wanted them to appear as if they could fold up, so I could not ship lap them together, though that in some ways may have been easier. The dilemma was attaching them to the cross cleats, which sounds simple but was a bit complicated.
The issue was the offset of the legs. Because the legs were not ship-lapped, one side of the leg would obviously offset, in this case ¾ of an inch. So my solution was to make a filler board to make up the gap made by the offset. At that, I wanted the board to match the angles and width of the cleat board as closely as possible, so I spent a good deal of time clamping and measuring. Once I was as sure of myself as I was going to get, I made the cuts, planed it to final size and started drilling holes for the quarter inch hardware I purchased for the project. I won’t lie, those first couple of holes were nerve-wracking, because a mistake would cost me several more hours of work, but once I got moving things went relatively smoothly. It took more than two hours, but in the end I had a finished leg assembly.
Sunday morning I started on the second assembly, and using lessons learned from the previous night’s experience, I had it finished and ready to attach in under an hour, so rather than leaving those two assemblies on top of the workbench, I did just that attached them to the desktop using some angle brackets. I hadn’t planned to do an assembly to be honest, but curiosity got the best of me. The good news is that so far it looks pretty good. Admittedly, I was a little disappointed that the breadboard ends needed to be removed, but it doesn’t look bad in my opinion. But the better news is the fact that the legs all sit level with the ground. Generally, when making a table, there is usually a bit of wobble. As of right now the table sits nicely, and when I placed a level on the top I found it dead flat. At that, the table does rock a bit back and forth, but considering it is not permanently attached to the top yet, and considering the leg assemblies haven’t been joined together yet with any cross bracing, that was to be expected.
Lastly, I removed the assembled table from my garage and placed it in the family room, where I think it will be much safer. Over the years, I’ve found out the hard way that leaving unassembled furniture projects in my garage is a recipe for disaster. Maybe it’s gremlins; I don’t know, but whatever it is my projects seem to take a beating if they sit in the garage for too long, so I was taking absolutely no chances. In any event, the cat seems to like it, because as soon as I brought it inside the house she promptly hopped onto it, sprawled out, and took a nap.
Next weekend I will mill down another board to use for the cross bracing as well as the desktop drawer unit. Thankfully, I already have the drawer unit finalized in my mind, so the construction should have no unwanted surprises. So with a little luck I could quite possibly have a desk ready for finish a week from now.
On another note, some of you (or none of you) may be wondering why I did not post last week. Well, I had the very good fortune to go to Washington DC and not only take a tour of the White House, but to visit Mount Vernon as well. The Mount Vernon trip was not planned, it just happened to fall into place, and because I had not been able to go there last time I was in DC, I made it a priority. I will only say of the trip that I was completely blown away. The furniture examples in Mount Vernon alone are beyond description, and I would have taken photos, but they are not allowed inside the house itself. And because I believe that rules are a good thing (they are hardly “for fools” as some in the woodworking world would claim) I did not attempt any, and instead purchased a very nice book with photos that are much better than those I would have taken anyway.
My family, who was skeptical about the Mount Vernon visit in part because the day was cool, cloudy, and damp, was nonetheless blown away. My daughter in particular was completely awestruck. But the highlight, for all of us, was visiting the final resting place of George and Martha Washington and paying our respects. When I say that this trip was beyond inspirational and much more of a spiritual experience, I am understating to the highest degree. Upon leaving Mount Vernon, my admiration of George Washington, which was already immense, grew even greater. And more than ever I am committed to making this desk to the highest level I possibly can.